- 您现在的位置：买卖IC网 > Sheet目录336 > LDS8620-002-T2 (IXYS)IC LED DRIVER FLASH 16WQFN
LDS8620
programmed by first selecting the register address
and then programming data into that register.
An internal counter records the number of falling
edges to identify the address and data. The address
is serially programmed adhering to low and high
duration time delays. One down pulse corresponds to
register 1 being selected. Two down pulses
correspond to register 2 being selected and so on up
to register 5. t LO and t HI must be within 200ns to
100 μ s. Anything below 200ns may be ignored.
Once the final rising edge of the address pointer is
programmed, the user must wait longer than 500 μ s
before programming the first data pulse. Any falling
edge after that will be recognised as a first data
pulse.
Data in a register is reset once it is selected by the
address pointer. If a register is selected but no data is
programmed, the next pulse sequence will be
recognized as data only. Do not select register
without data sending because it may disrupt normal
device operation.
Once the final rising edge of the data pulses is
programmed, the user must wait at least 2 ms before
programming another address. If programming fails
or is interrupted, the user must wait t RESETDELAY 2 ms
from the last rising edge before reprogramming can
commence.
REG5 also triggers the internal charge pump. This
forces the charge pump to start from 1-x mode and
determine the correct mode it should operate to drive
the LEDs most efficiently. If V IN has risen or the
device has been reprogrammed to other LED values,
it is recommended to trigger this reset allowing the
charge pump to run in the most efficient mode.
To power-down the device and turn-off all current
sources, the EN/SET input should be kept low for a
duration t OFF of 1.5 ms or more. The driver typically
powers-down with a delay of about 1 ms. All register
data are cleared/reset.
Device allows multi flash mode operation using
1-wire interface. In this case, Registers 2, 3 or 4
should be programmed first to set output current.
Register Reg1 should be used to start flash event
with one or two channels depend on number of LED
turned on. Flash starts t DATADELAY (2 ms) later after
last data pulse. Use Reg1 address without data (one
pulse) to turn off flash. Next flash event may start any
time after t RESETDELAY (2 ms) by selecting register
Reg1 with data. (See Figure 3 for an example – multi
flash mode with maximum output current and all
LEDs turned on during the flash.)
Protection Modes
The LDS8620 has follow protection modes:
1. LED short to V OUT protection
Upon
EN/SET pin goes high,
the
LDS8620
If LED pin is shorted to V OUT , LED burned out
automatically seeks an address instruction. The
device requires a minimum 10 μ s delay to ensure the
initialization of the internal logic at power-up. After
this time delay, EN/SET pin may be set high and the
device registers may be programmed adhering to the
timing constraints shown in Figure 1.
Register REG1 allows select the LEDs to be turned
on. Each of LEDs can be turned on independently by
setting the respective bit to 1.
Register REG2 allows to set the same current for all
channels. REG3 and REG4 allow to set the current
respectively in LED A and B. The LEDs can be
programmed with independent current values.
REG5 contains the return lockout (RTLKO) bit. This
stops the charge pump returning to 1-x mode. One
pulse sets it to 1. Two pulses set RTLKO to 0. When
RTLKO is set to 1, the charge pump cannot
automatically return to 1-x mode when in one of the
charge pump modes. The device can however move
from 1-x to 1.5-x or 2-x if the input voltage is not
sufficient to drive the programmed LED currents.
becomes as short circuit, or LED pin voltage is within
(V OUT - 1.5 V) range, LDS8620 recognizes this
condition as “LED Short” and disables this channel
with 750 μA control current. If LED pin voltage is less
than (Vout – 1.5 V), LDS8620 restores LED current at
this particular channel to programmed value.
2. V OUT Over-Voltage Protection
The charge pump’ output voltage V OUT automatically
limits at about 6.2 V maximum. This is to prevent the
output pin from exceeding its absolute maximum
rating.
3. V OUT Short Circuit Protection
If V OUT is shorted to ground before LDS8620 is
enabled, input current may increase up to 200 –
300 mA within 20 μs after enable and is limited to 35
– 40 mA after that.
4. Over-Temperature Protection
If the die temperature exceeds +150°C, the driver will
enter shutdown mode. The LDS8620 requires restart
after die temperature falls below 130°C.
? 2009 IXYS Corp.
Characteristics subject to change without notice
8
Doc. No. 8620DS, Rev. N1.1
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LDS8621002-T2-960
IC LED DRIVER FLASH 16WQFN
LDS8680008-T2
IC LED DRIVER PHOTO FLASH 16WQFN
LDS8681008-T2
IC LED DRIVER PHOTO FLASH 16WQFN
LDS8711
IC LED DRIVER PWM 32MA 8TDFN
LDS8720
IC LED DRIVER PWM 25MA 8TDFN
LDS8724
IC LED DRIVER PWM 25MA 8TDFN
LDS8726
IC LED DRIVER PWM 25MA 8TDFN
LDS8845-002-T2
IC LED DVR WHT/CLR BCKLGT 16WQFN
相关代理商/技术参数
LDS8621-002-T2
功能描述:LED照明驱动器 200mA Dual Output Flash/Lamp Drvr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
LDS8621002-T2-960
功能描述:IC LED DRIVER FLASH 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C
LDS8640-002-T3
功能描述:LED照明驱动器 400mA Dual Output Flash/Lamp Drvr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
LDS8640-008-T2
功能描述:IC LED DRIVER 200MA 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C
LDS8641-002-T4
功能描述:LED照明驱动器 400mA Dual Output Flash/Lamp Drvr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
LDS8641-008-T2
功能描述:IC LED DRIVER 200MA 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C
LDS8680-002-T5
功能描述:LED照明驱动器 800mA Dual Output Flash/Lamp Drvr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
LDS8680008-T2
功能描述:IC LED DRIVER PHOTO FLASH 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C